Profile

New User

New to Graphy Publications? Create an account to get started today.

Registered Users

Have an account? Sign in now.

How to Cite | Author Information | Publication History
International Journal of Metallurgical & Materials Engineering Volume 3 (2017), Article ID 3:IJMME-139, 10 pages
http://dx.doi.org/10.15344/2455-2372/2017/139
Review Article
The Effect of Size on the Distortion Behavior After Carburisation and Quenching Processes of Gears

Koen Decroos1,2,* and Marc Seefeldt3

1Opti Quench, 9000 Gent, Belgium
2University of Gent, Faculty of Engineering, Department of Metallurgy and Materials Science, 9000 Gent, Belgium
3Catholic University of Leuven, Faculty of Engineering, Department of Metallurgy and Materials Engineering , 3001 Heverlee (Leuven), Belgium
Prof. Koen Decroos, University of Gent, Faculty of Engineering, Department of Metallurgy and Materials Science, 9000 Gent, Belgium, Tel: +32 16321274; E-mail: koenraad.decroos@mtm.kuleuven.be
25 November 2017; 27 December 2017; 29 December 2017
Decroos K, Seefeldt M (2017) The Effect of Size on the Distortion Behavior After Carburisation and Quenching Processes of Gears. Int J Metall Mater Eng 3: 139. doi: https://doi.org/10.15344/2455-2372/2017/139
© 2017 Decroos et al. This is an open-access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.

References

  1. Davis JR (2005) Gear Materials, Properties, and Manufacture. ASM International. View
  2. Lapman S (1990) Introduction to Surface hardening of Steels. In: ASM (Ed.), ASM Metals HandBook Vol. 4: heat treating.
  3. Pan J (2002) Factors Affecting Final Part Shaping. In: M. Howes, T. Inoue, G. Totten (Eds.), Handbook of Residual Stress and Deformation of Steel, ASM International.
  4. Nallathambi AK, Kaymak Y, Specht E, Bertram A (2010) Sensitivity of material properties on distortion and residual stresses during metal quenching processes. J Mat Proc Tech 210: 204-211. View
  5. ANSYS (2008) ANSYS 11.0 Complete User's Manual Set.
  6. Kang SH, Im YT (2007) Three-dimensional thermo-elastic-plastic finite element modeling of quenching process of plain-carbon steel in couple with phase transformation. Int J Mech Sc 49: 423-439. View
  7. Huiping L, Guoqun Z, Shanting N, Chuanzhen H (2007) FEM simulation of quenching process and experimental verification of simulation results. Mat ScEng A 452-453: 705-714. View
  8. Sugianto A, Narazaki M, Kogawara M, Shirayori A, Kim SY, et al. (2009) Numerical simulation and experimental verification of carburizingquenching process of SCr420H steel helical gear. J Mat Proc 209: 3597- 3609. View
  9. Decroos K, Seefeldt M (2013) Modelling of distortions after carburisation and quenching processes of large gears, submitted to Model. Simul Mater Sci Eng 21: 3. View
  10. HKDH, Bhadeshia R, Honeycombe (2003) Steels, Microstructure and Properties, Oxford, Elsevier.
  11. Scheil E (1935) Anlaufzeit der Ausenitumwandlung. Arch Eisenh 12: 564- 567. View
  12. Avrami M (1939) Kinetics of phase change i-iii. J Chem Phys 7: 1103-1112.
  13. Koistinen DP, Marburger RE (1959) A gerneral equation prescribing the extend of the austenite-martensite transformation in pure iron-carbon alloys and plane carbon steels. Acta Met 7: 59-60. View
  14. Popova LE, Popov AA (1991) Diagrams of transformation of austenite in steels and beta solution in Titanium. Moscow, Metallurgiya.
  15. Lindgren LE (2006) Numerical modelling of welding. Comp Meth Appl Mech Engrg 195: 6710-6736. View
  16. Houtte PV (1994) Application of plastic potentials to strain rate sensitive and insensitive anisotropic materials. Int J of Plast 10: 719-748. View
  17. Mises RV (1928) Mechanik der Plastischen Formänderung der Kristallen. Z angew Math Mech 8: 161-185. View
  18. Greenwood GW, Johnson RH (1965) The deformation of metals under small stress during phase transformation. Proc Royal Sc A 283: 403-422. View
  19. Zienkiewitz OC, Taylor RL (2000) The Finite Element Method Vol. 2 Solid Mechanics. Butterworth-Heinemann. View
  20. Decroos K, Ohms C, Houbaert Y (2008) Ceramics Transactions. 200: 115- 123.
  21. Alberg H, Berglund D (2003) Comparison of Plastic, Viscoplastic, and Creep Models when Modelling Welding and Stress Relief Heat Treatment. Comp Meth App Mech Eng 192: 5189-5208. View
  22. M. Narazaki, In: M. Howes, T. Inoue, G. Totten, (Eds.), Handbook of Residual Stress and Deformation of Steel, ASM International, 2002, pp. 248-295.
Best viewed in Mozilla Firefox, Google Chrome, Safari, Above IE 9.0 version
Privacy Policy | Copyright & Permissions
Copyright © 2013-2024 Graphy Publications, All Rights Reserved.